Model 250i
The Dynojet Load Control System was developed through years of experience with over 3,900 dynamometer installations worldwide. The design is easy to operate and provides the function of steady state load control. Dynojet's Load Control System uses the latest in eddy current power absorption technology, which combines with our easy to use software, so any technician can get repeatable, consistent results. The Load Control software provides the technician with the ability to control vehicle RPM or Speed at any throttle opening. Through our exclusive closed-loop software design, the vehicle is automatically held at your pre-determined setting. With the addition of the optional torque cell package, the dyno has the capability of a more complete range of tests, including step and sweep tests and wind drag simulation.
Model 250i : Details
- Closed-loop control of Speed or RPM
- Easy-to-use software, push putton operation
- Test Vehicles at full or partial throttle
- Absorption unit capable of 858 lb/ft torque
- Compact design
- Optional closed -loop Torque control module
- Inertia Dynamometer Chassis with standard wheel base up to 84 inches
- Measures up to 750 horsepower
- Primary Wire Inductive tachometer pickup
- Secondary Inductive Pickups (spark plug clamps connect directly to spark plug wires)
- WinPEP7 Software, Windows 95 to Windows XP
- Bike Starter System (requires battery)
- Wheel Lock
- Installation and Operation manuals provided on CD-ROM
- Training voucher for MMI Dyno operations course (Orlando or Phoenix)
- Technical support helpline
- 1 Year replacement part warranty
- Dynoware EX+ hardware includes:
- CPU Module: Com Port Interface, runs on 12VDC & 110VAC
- Dyno Module: Sends and receives data to and from the Dyno
- Atmospheric Sensing Module: Automatically measures absolute pressure, air temperature and relative humidity
- RPM Module: Receives and processes ignition (spark) signals for correct engine speed measurement
Model 250i : Specifications
- Dedicated 240v 30amp single-phase circuit
- Maximum Horsepower: 750 hp
- Maximum Speed: 200 mph (322 kph)
- Timing Accuracy +/- 1 microsecond
- Drum Speed Accuracy +/-/100th mph
- RPM Accuracy +/-1/10th rpm
Model 250i Load Control
The Dynojet Load Control System was developed through years of experience with over 3,900 dynamometer installations worldwide. The design is easy to operate and provides the function of steady-state load control.
Dynojet's Load Control System uses the latest in eddy current power absorption technology, which combines with our easy-to-use software to give any technician repeatable, consistent results. The Load Control software provides a technician with the ability to control vehicle RPM or speed at any throttle opening. Through our exclusive closed-loop software design, the vehicle is automatically held at the pre determined setting.
DIMENSIONS (Above Ground Model) |
Base Length |
29.83" (202.8 cm) |
Base Width |
70.71" (179.6 cm) |
Base Height |
18.10" (45.9 cm) |
Drum Diameter |
18" (45.72 cm) per wheel |
Drum Width |
20" (50.80 cm) |
Drum Concentricity |
+/- 0.001" (+/-0.025 mm) |
Maximum Bike Length
(Front of Front Wheel to Center of Rear Wheel) |
84" (213.4 cm) |
WEIGHT |
Dynamometer |
2375 lbs (1077 Kg) (approx.) |
Crated Dynamometer |
2500 lbs (1134 Kg) (approx.) |
MATERIAL |
Drum |
A 106 Steel |
Shaft |
2 3/16 inch 1144 turned, ground & polished steel |
Frame |
10 Gauge Cold Roll Steel |
PERFORMANCE SPECIFICATIONS |
Modelled Mass (Standard) |
450 lbs (204 Kg) (approx.) |
Modelled Mass (High-Inertia) |
650 lbs (295 Kg) (approx.) |
Maximum Horsepower |
750 hp |
Maximum Speed |
200 mph |
Maximum Torque |
500 ft/lbs |
Temperature Range |
32°F to 158°F (0°C to 70°C) |
GENERAL |
Calibration |
Not required (factory calibrated) |
Inductive Pickup |
Primary Wire RPM Pickup |
Power Requirements |
240v 30amp single phase circuit |
Remote Switches |
Remote Software Control |
HARDWARE |
Timing Accuracy |
+/- 1 microseconds |
Drum Speed |
+/- 1/100th MPH |
RPM Accuracy |
+/- 1/10th RPM |
|
